Tankless or Demand Water Heaters Installation

By | December 16, 2010

Demand (tankless or instantaneous) water heaters

provide hot water only as it is needed. They don’t produce the standby energy losses associated with storage water heaters, which can save you money. Here you’ll find basic information about how they work, whether a demand water heater might be right for your home, and what criteria to use when selecting the right model.

Above is an Illustration of an electric demand water heater. At the top of the image, the heating unit is shown. Cold water flows in one end of a pipe, flows through and around several curved pipes over the heating elements, and out the other end as hot water. Beneath the heating unit, a typical sink setup is shown. The sink has two pipes coming out the bottom, one for the hot water line and one for the cold water line. Both pipes lead to the heating unit, which is installed in close proximity to the area of hot water use, and is connected to a power source (110 or 220 volts).

How Do Tankless Water Heaters Work

Demand water heaters heat water directly without the use of a storage tank. Therefore, they avoid the standby heat losses associated with storage water heaters. When a hot water tap is turned on, cold water travels through a pipe into the unit. Either a gas burner or an electric element heats the water. As a result, demand water heaters deliver a constant supply of hot water. You don’t need to wait for a storage tank to fill up with enough hot water. However, a demand water heater’s output limits the flow rate.

Typically, demand water heaters provide hot water at a rate of 2–5 gallons (7.6–15.2 liters) per minute. Gas-fired demand water heaters produce higher flow rates than electric ones. Sometimes, however, even the largest, gas-fired model cannot supply enough hot water for simultaneous, multiple uses in large households. For example, taking a shower and running the dishwasher at the same time can stretch a demand water heater to its limit. To overcome this problem, you can install two or more demand water heaters, connected in parallel for simultaneous demands of hot water. You can also install separate demand water heaters for appliances—such as a clothes washer or dishwater—that use a lot of hot water in your home.

Other applications for demand water heaters include the following:

* Remote bathrooms or hot tubs
* Booster for appliances, such as dishwashers or clothes washers
* Booster for a solar water heating system.

Although gas-fired demand water heaters tend to have higher flow rates than electric ones, they can waste energy if they have a constantly burning pilot light. This can sometimes offset the elimination of standby energy losses when compared to a storage water heater. In a gas-fired storage water heater, the pilot light heats the water in the tank so the energy isn’t wasted. The cost of operating a pilot light in a demand water heater varies from model to model. Ask the manufacturer how much gas the pilot light uses for the model you’re considering. If you purchase a model that uses a standing pilot light, you can always turn it off when it’s not in use to save energy. Also consider models that have an intermittent ignition device (IID) instead of a standing pilot light. This device resembles the spark ignition device on some gas kitchen ranges and ovens.

For homes that use 41 gallons or less of hot water daily, demand water heaters can be 24%–34% more energy efficient than conventional storage tank water heaters. They can be 8%–14% more energy efficient for homes that use a lot of hot water—around 86 gallons per day. You can achieve even greater energy savings of 27%–50% if you install a demand water heater at each hot water outlet.

Selecting a Demand Water Heater

Demand water heaters cost more than conventional storage water heaters. However, you may find that a demand water heater may have lower operating and energy costs, which could offset its higher purchase price.

Before buying a demand water heater, you also need to consider the following:

* Size
* Fuel type and availability.
* Energy efficiency (energy factor)
* Estimate costs.

Proper installation and maintenance of your demand water heater can optimize its energy efficiency.
Proper installation depends on many factors. These factors include fuel type, climate, local building code requirements, and safety issues, especially concerning the combustion of gas-fired water heaters. Therefore, it’s best to have a qualified plumbing and heating contractor like Plus Plumbing install your demand water heater.

Waterloo Region Plus Plumbing Installs Tankless Water Heaters

Plus Plumbing are specialists in the installation of all kinds of water heaters. You can purchase your Water Heater wherever you wish or we can get it for you and we will install it, meeting all safety standards and codes. We can install your water heater in Kitchener,Waterloo,Cambridge or any of the surrounding towns in Waterloo Region. When you are ready call us at 519-465-2697.

4 thoughts on “Tankless or Demand Water Heaters Installation

  1. monty kerr

    I am in need of a short(about 5 inches) electric water heater element 220 volt 1500 watt screw in with 1 1/4 inch thread. it could be larger wattage, up to 3000 watts.
    seems these elements are hard to find, I wonder why???????
    CAN YOU SUPPLY ME WITH 2 OF THESE UNITS?
    MONTY

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *